Tired of ads? Remove them as a Premium Member. Read more

2010 FORD Fusion Maintenance Light Reset Instructions

Instructions Comments Off on 2010 FORD Fusion Maintenance Light Reset Instructions

1. Turn the ignition to run (one position before starting engine).
2. Press and release SETUP to display "OIL LIFE XXX% HOLD RESET = NEW".
3. Press and hold RESET for 2 seconds and release to reset the oil life to 100%.
4. Turn the ignition off and then start the engine to verify the indicator has been reset.




2011 FORD Fiesta Maintenance Light Reset Instructions

Instructions Comments Off on 2011 FORD Fiesta Maintenance Light Reset Instructions

1. Turn the ignition to run (one position before starting engine).
2. Press the brake and gas pedals at the same time for 20 seconds.
3. An oil lamp with wrench will display with the message ENGINE OIL CHANGE DUE NEXT SERVICE.
4. Turn the ignition off and then start the engine to verify the indicator has been reset.




2008 CHRYSLER Aspen Maintenance Light Reset Instructions

Instructions Comments Off on 2008 CHRYSLER Aspen Maintenance Light Reset Instructions

1. Turn the ignition to run (one position before starting engine).
2. Fully depress the accelerator pedal slowly three times within 10 seconds.
3. Turn the ignition off and then start the engine to verify the indicator has been reset.




2006-2007 Explorer/Sport Trac Maintenance Light Reset Instructions

Instructions Comments Off on 2006-2007 Explorer/Sport Trac Maintenance Light Reset Instructions

1. Turn the ignition to run (one position before starting engine).
"2. Enter SYSTEM CHECK to display ""OIL XXX% OIL LIFE OK""."
"3. Press RESET button to display ""HOLD RESET IF NEW OIL""."
"4. Press and hold the RESET button for more than two seconds. Oil life is set to 100% and ""OIL CHANGE SET TO 100%"" is displayed."
5. Turn the ignition off and then start the engine to verify the indicator has been reset.




2005 CHEVROLET Cobalt Maintenance Light Reset Instructions

Instructions Comments Off on 2005 CHEVROLET Cobalt Maintenance Light Reset Instructions

1. Turn the ignition to run (one position before starting engine).
2. Press the INFO and RESET (arrow) buttons on the DIC at the same time to enter the personalization menu.
3. Press the INFO button to scroll through the menu until OIL LIFE RESET is displayed.
4. Press and hold the RESET button until the DIC display shows ACKNOWLEDGED. This will tell you the system has been reset.
5. Turn the ignition off and then start the engine to verify the indicator has been reset.




2010 FORD Mustang Maintenance Light Reset Instructions

Instructions Comments Off on 2010 FORD Mustang Maintenance Light Reset Instructions

1. Turn the ignition to run (one position before starting engine).
2. Press and release SETUP to display "OIL LIFE XXX% HOLD RESET = NEW".
3. Press and hold RESET for 2 seconds and release to reset the oil life to 100%.
4. Turn the ignition off and then start the engine to verify the indicator has been reset.




2011 Edge Maintenance Light Reset Instructions

Instructions Comments Off on 2011 Edge Maintenance Light Reset Instructions

1. Turn the ignition to run (one position before starting engine).
2. Use the left steering wheel controls to scroll through the message center. Press the up/down arrow repeatedly until OIL LIFE RESET is selected.
3. Press OK to select this option and display SET XXX%.
4. Press and hold OK again for 2 seconds to reset.
5. Turn the ignition off and then start the engine to verify the indicator has been reset.
*Some models may require you to select SETTINGS to access the OIL LIFE RESET.




2008 DODGE Charger Maintenance Light Reset Instructions

Instructions Comments Off on 2008 DODGE Charger Maintenance Light Reset Instructions

1. Turn the ignition to run (one position before starting engine).
2. Fully depress the accelerator pedal slowly three times within 10 seconds.
3. Turn the ignition off and then start the engine to verify the indicator has been reset.




2011 CHRYSLER 200 Maintenance Light Reset Instructions

Instructions Comments Off on 2011 CHRYSLER 200 Maintenance Light Reset Instructions

1. Turn the ignition to run (one position before starting engine).
2. Fully depress the accelerator pedal slowly three times within 10 seconds.
3. Turn the ignition off and then start the engine to verify the indicator has been reset.




2004-2009 Envoy/Trailblazer Maintenance Light Reset Instructions

Instructions Comments Off on 2004-2009 Envoy/Trailblazer Maintenance Light Reset Instructions

1. Turn the ignition to run (one position before starting engine).
2. Immediately after Step 1 press and release the gas pedal 3 times within 5 seconds.
3. If the Change Oil Soon light flashes the system is resetting.
4. Turn the ignition off and then start the engine to verify the indicator has been reset.





Remove ads as a Premium Member. Read More