Tired of ads? Remove them as a Premium Member. Read more

1989 PONTIAC 6000 Maintenance Light Reset Instructions

Instructions Comments Off on 1989 PONTIAC 6000 Maintenance Light Reset Instructions

1. Turn the ignition to run (one position before starting engine).
2. Press and release the SERVICE REMINDER button until the desired item is displayed.
3. When the desired item is displayed, do not release SERVICE REMINDER button.
4. After button has been pressed for approximately 10 seconds, the service interval mileage display will begin to count down in 500 mile/km intervals.
5. When desired service interval mileage is reached, release button.
6. Turn the ignition off and then start the engine to verify the indicator has been reset.




1988 PONTIAC 6000 Maintenance Light Reset Instructions

Instructions Comments Off on 1988 PONTIAC 6000 Maintenance Light Reset Instructions

1. Turn the ignition to run (one position before starting engine).
2. Press and release the SERVICE REMINDER button until the desired item is displayed.
3. When the desired item is displayed, do not release SERVICE REMINDER button.
4. After button has been pressed for approximately 10 seconds, the service interval mileage display will begin to count down in 500 mile/km intervals.
5. When desired service interval mileage is reached, release button.
6. Turn the ignition off and then start the engine to verify the indicator has been reset.




1987 PONTIAC 6000 Maintenance Light Reset Instructions

Instructions Comments Off on 1987 PONTIAC 6000 Maintenance Light Reset Instructions

1. Turn the ignition to run (one position before starting engine).
2. Press and release the SERVICE REMINDER button until the desired item is displayed.
3. When the desired item is displayed, do not release SERVICE REMINDER button.
4. After button has been pressed for approximately 10 seconds, the service interval mileage display will begin to count down in 500 mile/km intervals.
5. When desired service interval mileage is reached, release button.
6. Turn the ignition off and then start the engine to verify the indicator has been reset.




1986 PONTIAC 6000 Maintenance Light Reset Instructions

Instructions Comments Off on 1986 PONTIAC 6000 Maintenance Light Reset Instructions

1. Turn the ignition to run (one position before starting engine).
2. Press and release the SERVICE REMINDER button until the desired item is displayed.
3. When the desired item is displayed, do not release SERVICE REMINDER button.
4. After button has been pressed for approximately 10 seconds, the service interval mileage display will begin to count down in 500 mile/km intervals.
5. When desired service interval mileage is reached, release button.
6. Turn the ignition off and then start the engine to verify the indicator has been reset.




2013 NISSAN Frontier Maintenance Light Reset Instructions

Instructions Comments Off on 2013 NISSAN Frontier Maintenance Light Reset Instructions

1. Turn the ignition to run (one position before starting engine). The maintenance information (the wrench symbol and distance to change a maintenance item) comes on for about 5 seconds and then turns off.
2. Push the trip button and hold for 3 seconds while the wrench symbol and maintenance information are
are displayed. The symbol and distance display will start flashing and the display shows the current interval (ie. 5000KM).
3. Push the trip button to increase the interval distance. Each step increases the interval by 1000km. The interval distance can be set up to 30000km after the display returns to 0.
4. If no further action is made, the display returns to the previous mode and the new interval is set. If the interval distance is set to 0, the display will skip the maintenance information when the ignition is placed in run or start mode.
5. Turn the ignition off and then start the engine to verify the indicator has been reset.




2013 NISSAN Z Maintenance Light Reset Instructions

Instructions Comments Off on 2013 NISSAN Z Maintenance Light Reset Instructions

1. Turn the ignition to run (push START/STOP button once).
2. Press the square) button, located on the instrument panel just behind the steering wheel to the left, to displaythe SETTINGS mode.
3. In the setting mode screen press the circle button to move to MAINTENANCE.
4. Set a desired interval by pushing the circle button to highlight ENGINE OIL and pressing the square button. The reset mode will open up and allow you to enter the desired distance.
5. Select RESET and select new time or distance.
6. Repeat step 3 for ENGINE OIL FILTER.
7. Turn the ignition off and then start the engine to verify the indicator has been reset.




2012 NISSAN Z Maintenance Light Reset Instructions

Instructions Comments Off on 2012 NISSAN Z Maintenance Light Reset Instructions

1. Turn the ignition to run (push START/STOP button once).
2. Press the square) button, located on the instrument panel just behind the steering wheel to the left, to displaythe SETTINGS mode.
3. In the setting mode screen press the circle button to move to MAINTENANCE.
4. Set a desired interval by pushing the circle button to highlight ENGINE OIL and pressing the square button. The reset mode will open up and allow you to enter the desired distance.
5. Select RESET and select new time or distance.
6. Repeat step 3 for ENGINE OIL FILTER.
7. Turn the ignition off and then start the engine to verify the indicator has been reset.




2011 NISSAN Z Maintenance Light Reset Instructions

Instructions Comments Off on 2011 NISSAN Z Maintenance Light Reset Instructions

1. Turn the ignition to run (push START/STOP button once).
2. Press the square) button, located on the instrument panel just behind the steering wheel to the left, to displaythe SETTINGS mode.
3. In the setting mode screen press the circle button to move to MAINTENANCE.
4. Set a desired interval by pushing the circle button to highlight ENGINE OIL and pressing the square button. The reset mode will open up and allow you to enter the desired distance.
5. Select RESET and select new time or distance.
6. Repeat step 3 for ENGINE OIL FILTER.
7. Turn the ignition off and then start the engine to verify the indicator has been reset.




2010 NISSAN Z Maintenance Light Reset Instructions

Instructions Comments Off on 2010 NISSAN Z Maintenance Light Reset Instructions

1. Turn the ignition to run (push START/STOP button once).
2. Press the square) button, located on the instrument panel just behind the steering wheel to the left, to displaythe SETTINGS mode.
3. In the setting mode screen press the circle button to move to MAINTENANCE.
4. Set a desired interval by pushing the circle button to highlight ENGINE OIL and pressing the square button. The reset mode will open up and allow you to enter the desired distance.
5. Select RESET and select new time or distance.
6. Repeat step 3 for ENGINE OIL FILTER.
7. Turn the ignition off and then start the engine to verify the indicator has been reset.




2009 NISSAN Z Maintenance Light Reset Instructions

Instructions Comments Off on 2009 NISSAN Z Maintenance Light Reset Instructions

1. Turn the ignition to run (push START/STOP button once).
2. Press the square) button, located on the instrument panel just behind the steering wheel to the left, to displaythe SETTINGS mode.
3. In the setting mode screen press the circle button to move to MAINTENANCE.
4. Set a desired interval by pushing the circle button to highlight ENGINE OIL and pressing the square button. The reset mode will open up and allow you to enter the desired distance.
5. Select RESET and select new time or distance.
6. Repeat step 3 for ENGINE OIL FILTER.
7. Turn the ignition off and then start the engine to verify the indicator has been reset.





Remove ads as a Premium Member. Read More