Manual Reset using DIS and Reset Knobs:
1. Turn off the ignition
2. Locate the Driver Information System (DIS) in the instrument panel.
3. Locate the reset buttons (WRENCH button and 0,0 button)
4. Do the following to display the SERVICE! Message in the DIS:
i) Press and hold the Wrench button.
ii) Turn on the ignition - do not start the engine.
iii) Release the WRENCH button.
5. Do the following to display the next service interval (SERVICE in ##MI)
i) Press and hold the 0,0 button until the message changes.
ii) Release the 0,0 button.
6. Turn off the ignition.
7. Start the engine and verify indicator has been reset.
Manual Reset using DIS and Reset Knobs:
1. Turn off the ignition
2. Locate the Driver Information System (DIS) in the instrument panel.
3. Do the following to display the SERVICE! message in the display.
i) Press and hold the right RESET knob.
ii) Turn on the ignition - do not start the engine.
iii) Release the knob.
4. Do the following to display the next service interval (SERVICE IN ##MI)
i) Press and hold the right RESET knob.
ii) Release the knob.
5. Turn off the ignition.
6. Start the engine and verify indicator has been reset.

2016 Chevrolet Spark

To reset the 2016 Chevrolet Spark remaining oil life after a oil change, please follow these instructions:

1. Turn the ignition to run (one position before starting engine).
2. Press the DIC MENU button on the turn signal lever to enter the Vehicle Information Menu.
3. Use the thumbwheel to scroll through the menu items until you reach REMAINING OIL LIFE.
4. Press the SET/CLR button to reset the oil life at 100%.
5. Turn the ignition off and then start the engine to verify the indicator has been reset.

*No manual reset available. A diagnostic tool is required.

2016 Cadillac SRX

To reset the 2016 Cadillac SRX remaining oil life after a oil change, please follow these instructions:

1. Turn the ignition to run (one position before starting engine).
2. *Use the DIC controls on the right side of the steering wheel to display the REMAINING OIL LIFE.
3. Press SEL on the DIC controls.
4. Hold SEL down for a few seconds to reset the oil life to 100%.
5. Turn the ignition off and start the engine to verify the indicator has been reset.
*Remaining oil life can also be reset by depressing the gas pedal 3 times within 5 seconds instead of using the DIC.

Steering Wheel Controls

2012 Audi A7

To reset the 2012 Audi A7 oil change interval after a oil change, please follow these instructions:

1. Start the engine.
2. Press the CAR button to access the service menu.
3. From the CAR menu select CAR SYSTEMS.
4. From the CAR SYSTEMS menu select SERVICE INTERVALS.
5. Select RESET OIL CHANGE INTERVAL and confirm.
6. Turn off the igntion.
7. Start the engine and verify the indicator has been reset.

2001 Audi A6

To reset the 2006 Audi A6 service interval after a oil change, please follow these instructions:

Manual Reset using Odometer and Reset Knobs:
1. Turn off the ignition.
2. Locate the Service Interval Display, which is below the odometer.
3. Do the following to display the service OIL message in the Service interval display:
i) Press and hold the TRIP ODOMETER RESET knob.
ii) Turn on the ignition - do not start the engine.
iii) Release the TRIP ODOMETER RESET knob.
4. Pull out the CLOCK ADJUSTMENT knob.
5. Press and hold the TRIP ODOMETER RESET knob until the message changes to service INSP, then release the knob.
6. Pull out the CLOCK ADJUSTMENT knob, hold for 2 seconds and release.
7. Turn off the ignition.
8. Start the engine and verify indicator has been reset.
Manual Reset using DIS and Reset Knobs:
1. Turn off the ignition
2. Locate the Driver Information System (DIS) in the instrument panel.
3. Locate the reset buttons (WRENCH button and 0,0 button)
4. Do the following to display the SERVICE! Message in the DIS:
i) Press and hold the Wrench button.
ii) Turn on the ignition - do not start the engine.
iii) Release the WRENCH button.
5. Do the following to display the next service interval (SERVICE in ##MI)
i) Press and hold the 0,0 button until the message changes.
ii) Release the 0,0 button.
iii) Turn off the ignition.
6. Start the engine and verify indicator has been reset.

2016 Cadillac Escalade

To reset the 2016 Cadillac Escalade remaining oil life after a oil change, please follow these instructions:

1. Turn the ignition to run (one position before starting engine).
2. *Use the DIC controls on the right side of the steering wheel to display the REMAINING OIL LIFE.
3. Press SEL on the DIC controls.
4. Hold SEL down for a few seconds to reset the oil life to 100%.
5. Turn the ignition off and start the engine to verify the indicator has been reset.
*Remaining oil life can also be reset by depressing the gas pedal 3 times within 5 seconds instead of using the DIC.

Steering Wheel Controls

*Diagnostic Reset Tool Required
Manual Reset using DIS and Reset Knobs:
1. Turn off the ignition
2. Locate the Driver Information System (DIS) in the instrument panel.
3. Do the following to display the SERVICE! message in the display.
i) Press and hold the right RESET knob.
ii) Turn on the ignition.
iii) Release the knob.
4. Do the following to display the next service interval (SERVICE IN ##MI)
i) Press and hold the right RESET knob.
ii) Release the knob.
5. Turn off the ignition.
6. Start the engine and verify indicator has been reset.

2016 Cadillac XTS

To reset the 2016 Cadillac XTS remaining oil life after a oil change, please follow these instructions:

1. Turn the ignition to run (one position before starting engine).
2. *Use the DIC controls on the right side of the steering wheel to display the REMAINING OIL LIFE.
3. Press SEL on the DIC controls.
4. Hold SEL down for a few seconds to reset the oil life to 100%.
5. Turn the ignition off and start the engine to verify the indicator has been reset.
*Remaining oil life can also be reset by depressing the gas pedal 3 times within 5 seconds instead of using the DIC.

Steering Wheel Controls

1. Start the engine.
2. Press the CAR button to access the service menu.
3. From the CAR menu select CAR SYSTEMS.
4. From the CAR SYSTEMS menu select SERVICE INTERVALS.
5. Select RESET OIL CHANGE INTERVAL and confirm.
6. Turn off the igntion.
7. Start the engine and verify the indicator has been reset.