Tired of ads? Remove them as a Premium Member. Read more

1998 MERCEDES E – Class Maintenance Light Reset Instructions

Instructions Comments Off on 1998 MERCEDES E – Class Maintenance Light Reset Instructions

1. Turn the ignition to position 1 (one position before starting the engine).
2. Within 4 seconds press 0 button twice.
3. The present status for days or distance displays, within 10 seconds turn the electroninc key in steering lock to position 0.
4. Press and hold 0 button while turning electronic key in steering loack to position 2 again. The present status for days or distance displays once more. Continue to hold 0 button for approximately 10 seconds until a signal sounds and the display shows 10 000 (15000KM) for approximately 10 seconds.
5. Release 0 button, the status is reset.
6. Turn the ignition off and then start the engine to verify the indicator has been reset.




1997 MERCEDES E – Class Maintenance Light Reset Instructions

Instructions Comments Off on 1997 MERCEDES E – Class Maintenance Light Reset Instructions

1. Turn the ignition to position 1 (one position before starting the engine).
2. Within 4 seconds press 0 button twice.
3. The present status for days or distance displays, within 10 seconds turn the electroninc key in steering lock to position 0.
4. Press and hold 0 button while turning electronic key in steering loack to position 2 again. The present status for days or distance displays once more. Continue to hold 0 button for approximately 10 seconds until a signal sounds and the display shows 10 000 (15000KM) for approximately 10 seconds.
5. Release 0 button, the status is reset.
6. Turn the ignition off and then start the engine to verify the indicator has been reset.




2013 MERCEDES CLS – Class Maintenance Light Reset Instructions

Instructions Comments Off on 2013 MERCEDES CLS – Class Maintenance Light Reset Instructions

1. Turn the ignition to position 1 (one position before starting the engine).
2. The kilometre/mileage counter must appear in the display. If not displayed, press the down button repeatedly until displayed.
3. Press the left arrow button repeatedly until "trip" is displayed.
4. Press and hold phone button and then within 1 second press and hold down the OK button. Hold for 5 seconds then the workshop menu will be displayed "Vehicle data, Dynamometer Test, Change Brake Lining and ASSYST PLUS".
5. Select ASSYST PLUS and confirm with OK button.
6. Select FULL SERVICE and confirm with OK button.
7. Select CONFIRM SERV and confirm with OK button.
8. Select the oil used "Oil qual. 229.3" or "Oil qual. 229.5" and confirm with OK button.
9. Select YES and confirm with OK button.
10. Select CONFIRMATION and confirm selection by pressing OK button. "Full service carried out" appears in the display.
11. Press the OK button and exit the menu.
12. Turn the ignition off and then start the engine to verify the indicator has been reset.
*Close all doors, windows, hood and trunk when performing reset




2012 MERCEDES CLS – Class Maintenance Light Reset Instructions

Instructions Comments Off on 2012 MERCEDES CLS – Class Maintenance Light Reset Instructions

1. Turn the ignition to position 1 (one position before starting the engine).
2. The kilometre/mileage counter must appear in the display. If not displayed, press the down button repeatedly until displayed.
3. Press the left arrow button repeatedly until "trip" is displayed.
4. Press and hold phone button and then within 1 second press and hold down the OK button. Hold for 5 seconds then the workshop menu will be displayed "Vehicle data, Dynamometer Test, Change Brake Lining and ASSYST PLUS".
5. Select ASSYST PLUS and confirm with OK button.
6. Select FULL SERVICE and confirm with OK button.
7. Select CONFIRM SERV and confirm with OK button.
8. Select the oil used "Oil qual. 229.3" or "Oil qual. 229.5" and confirm with OK button.
9. Select YES and confirm with OK button.
10. Select CONFIRMATION and confirm selection by pressing OK button. "Full service carried out" appears in the display.
11. Press the OK button and exit the menu.
12. Turn the ignition off and then start the engine to verify the indicator has been reset.
*Close all doors, windows, hood and trunk when performing reset




2011 MERCEDES CLS – Class Maintenance Light Reset Instructions

Instructions Comments Off on 2011 MERCEDES CLS – Class Maintenance Light Reset Instructions

1. Turn the ignition to position 1 (one position before starting the engine).
2. The kilometre/mileage counter must appear in the display. If not displayed, press the down button repeatedly until displayed.
3. Press the left arrow button repeatedly until "trip" is displayed.
4. Press and hold phone button and then within 1 second press and hold down the OK button. Hold for 5 seconds then the workshop menu will be displayed "Vehicle data, Dynamometer Test, Change Brake Lining and ASSYST PLUS".
5. Select ASSYST PLUS and confirm with OK button.
6. Select FULL SERVICE and confirm with OK button.
7. Select CONFIRM SERV and confirm with OK button.
8. Select the oil used "Oil qual. 229.3" or "Oil qual. 229.5" and confirm with OK button.
9. Select YES and confirm with OK button.
10. Select CONFIRMATION and confirm selection by pressing OK button. "Full service carried out" appears in the display.
11. Press the OK button and exit the menu.
12. Turn the ignition off and then start the engine to verify the indicator has been reset.
*Close all doors, windows, hood and trunk when performing reset




2010 MERCEDES CLS – Class Maintenance Light Reset Instructions

Instructions Comments Off on 2010 MERCEDES CLS – Class Maintenance Light Reset Instructions

1. Turn the ignition to position 1 (one position before starting the engine).
2. Press the system selection button (3 located on the lower left of the steering wheel) repeatedly until the kilometer reading is shown in the multi information display.)
3. Press the cluster illumination button (lower left of instrument panel) quickly 3 times. The battery voltage will be displayed.
4. Press the up or down buttons until the service menu appears.
5. Use the +/- buttons to select menu oprion "CONFIRM".
6. Press the system selection button uuntil "COMPLETE SERVICE" is selected.
7. Confirm "Complete Service" with system selection button. The display will show "SERVICE CONFIRMED".
8. Turn the ignition off and then start the engine to verify the indicator has been reset.




2009 MERCEDES CLS – Class Maintenance Light Reset Instructions

Instructions Comments Off on 2009 MERCEDES CLS – Class Maintenance Light Reset Instructions

1. Turn the ignition to position 1 (one position before starting the engine).
2. Press the system selection button (3 located on the lower left of the steering wheel) repeatedly until the kilometer reading is shown in the multi information display.)
3. Press the cluster illumination button (lower left of instrument panel) quickly 3 times. The battery voltage will be displayed.
4. Press the up or down buttons until the service menu appears.
5. Use the +/- buttons to select menu oprion "CONFIRM".
6. Press the system selection button uuntil "COMPLETE SERVICE" is selected.
7. Confirm "Complete Service" with system selection button. The display will show "SERVICE CONFIRMED".
8. Turn the ignition off and then start the engine to verify the indicator has been reset.




2008 MERCEDES CLS – Class Maintenance Light Reset Instructions

Instructions Comments Off on 2008 MERCEDES CLS – Class Maintenance Light Reset Instructions

1. Turn the ignition to position 1 (one position before starting the engine).
2. Press the system selection button (3 located on the lower left of the steering wheel) repeatedly until the kilometer reading is shown in the multi information display.)
3. Press the cluster illumination button (lower left of instrument panel) quickly 3 times. The battery voltage will be displayed.
4. Press the up or down buttons until the service menu appears.
5. Use the +/- buttons to select menu oprion "CONFIRM".
6. Press the system selection button uuntil "COMPLETE SERVICE" is selected.
7. Confirm "Complete Service" with system selection button. The display will show "SERVICE CONFIRMED".
8. Turn the ignition off and then start the engine to verify the indicator has been reset.




2007 MERCEDES CLS – Class Maintenance Light Reset Instructions

Instructions Comments Off on 2007 MERCEDES CLS – Class Maintenance Light Reset Instructions

1. Turn the ignition to position 1 (one position before starting the engine).
2. Press the system selection button (3 located on the lower left of the steering wheel) repeatedly until the kilometer reading is shown in the multi information display.)
3. Press the cluster illumination button (lower left of instrument panel) quickly 3 times. The battery voltage will be displayed.
4. Press the up or down buttons until the service menu appears.
5. Use the +/- buttons to select menu oprion "CONFIRM".
6. Press the system selection button uuntil "COMPLETE SERVICE" is selected.
7. Confirm "Complete Service" with system selection button. The display will show "SERVICE CONFIRMED".
8. Turn the ignition off and then start the engine to verify the indicator has been reset.




2013 MERCEDES CLK – Class Maintenance Light Reset Instructions

Instructions Comments Off on 2013 MERCEDES CLK – Class Maintenance Light Reset Instructions

1. Turn the ignition to position 1 (one position before starting the engine).
2. The kilometre/mileage counter must appear in the display. If not displayed, press the down button repeatedly until displayed.
3. Press the left arrow button repeatedly until "trip" is displayed.
4. Press and hold phone button and then within 1 second press and hold down the OK button. Hold for 5 seconds then the workshop menu will be displayed "Vehicle data, Dynamometer Test, Change Brake Lining and ASSYST PLUS".
5. Select ASSYST PLUS and confirm with OK button.
6. Select FULL SERVICE and confirm with OK button.
7. Select CONFIRM SERV and confirm with OK button.
8. Select the oil used "Oil qual. 229.3" or "Oil qual. 229.5" and confirm with OK button.
9. Select YES and confirm with OK button.
10. Select CONFIRMATION and confirm selection by pressing OK button. "Full service carried out" appears in the display.
11. Press the OK button and exit the menu.
12. Turn the ignition off and then start the engine to verify the indicator has been reset.
*Close all doors, windows, hood and trunk when performing reset





Remove ads as a Premium Member. Read More