The 2013 Toyota Tacoma is offered in a gasoline model.  After performing the oil change the maintenance data will need to be reset.  Follow these steps to reset this light:

1. Turn the ignition to run (one position before starting engine).

2. Ensure trip meter A reading is shown.  Turn ignition off.

3. While holding down the trip meter reset knob turn the ignition to run (one position before starting engine).

4. Hold down knob for at least 5 seconds.  The odometer indicates "000000" and the light goes off.  If the system fails to reset, the light will continue flashing.

5. Turn the ignition off and then start the engine to verify the indicator has been reset.

When doing the oil change and topping up fluids you will need to use the following specifications:

Engine Size	4 Cyl. 2.7L Gas	6 Cyl. 4.0L Gas
Motor Oil	0W20	5W30
Oil Capacity w/Filter	6.1 US qt. (5.8L)	2WD 4.8 US qt. (4.5L) 4WD 5.5 US qt. (5.2L)
Brake/Clutch Fluid	Dot 3	Dot 3
Engine Coolant	Toyota Super Long Life Coolant	Toyota Super Long Life Coolant
Power Steering Fluid	ATF DEXRON II or III	ATF DEXRON II or III
Automatic Transmission	4 Speed Model Toyota Genuine ATF Type T-IV 5 Speed Model Toyota Genuine ATF WS	4 Speed Model Toyota Genuine ATF Type T-IV 5 Speed Model Toyota Genuine ATF WS
Manual Transmission	SAE 75W90	SAE 75W90
Front Differential	Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent	Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent
Rear Differential	Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent	Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent
Transfer Case	SAE 75W90	SAE 75W90

You can cross reference the following Purolator filter numbers for your own application:

Engine Size	4 Cyl. 2.7L Gas	6 Cyl. 4.0L Gas
Oil Filter	L10241	L10241
Air Filter	A35625	A35578
Cabin Filter	C35644	C35644

 

 

 

 

 

 

 

 

 

Always consult the owner’s manual or manufacturer prior to any service

The 2013 Toyota Tundra is offered in a gasoline model.  After performing the oil change the maintenance data will need to be reset.  Follow these steps to reset this light:

1. Turn the ignition to run (one position before starting engine).

2. Ensure Trip Metre A reading is shown.  Turn the ignition off.

3. While holding down the trip meter reset knob turn the ignition to run (one position before starting engine).

Without multi-information display

4. Continue to press and hold the button until the trip meter displays "000000".

With multi-information display

4. Continue to press and hold the button until “MAINT REQD RESET MODE COMPLETE" appears on the multi-information display.

5. Turn the ignition off and then start the engine to verify the indicator has been reset.

 When doing the oil change and topping up fluids you will need to use the following specifications:

Engine Size	6 Cyl. 4.0L Gas	8 Cyl. 4.6L Gas	8 Cyl. 5.7L Gas
Motor Oil	0W20	0W20	0W20
Oil Capacity w/Filter	6.4 US qt. (6.1L)	7.9 US qt. (7.5L)	7.9 US qt. (7.5L)
Brake Fluid	Dot 3	Dot 3	Dot 3
Engine Coolant	Toyota Super Long Life Coolant	Toyota Super Long Life Coolant	Toyota Super Long Life Coolant
Power Steering Fluid	ATF DEXRON II or III	ATF DEXRON II or III	ATF DEXRON II or III
Automatic Transmission	Toyota Genuine ATF WS	Toyota Genuine ATF WS	Toyota Genuine ATF WS
Front Differential	Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent	Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent	Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent
Rear Differential	Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent	Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent	Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent
Transfer Case	SAE 75W90	SAE 75W90	SAE 75W90

You can cross reference the following Purolator filter numbers for your own application:

Engine Size	6 Cyl. 4.0L Gas	8 Cyl. 4.6L Gas	8 Cyl. 5.7L Gas
Oil Filter	L25609	L25702	L25702
Air Filter	A55799	A55799	A55799
Cabin Filter	C35667	C35667	C35667

The 2013 Toyota Sequoia is offered in a gasoline model.  After performing an oil change the maintenance data will need to be reset.  Follow these steps to reset this light:

1. Turn the ignition to run (one position before starting engine).

2. Ensure Trip Metre A reading is shown.  Turn the ignition off.

3. While holding down the trip meter reset knob turn the ignition to run (one position before starting engine).

Without multi-information display

4. Continue to press and hold the button until the trip meter displays "000000".

With multi-information display

4. Continue to press and hold the button until “MAINT REQD RESET MODE COMPLETE" appears on the multi-information display.

5. Turn the ignition off and then start the engine to verify the indicator has been reset.

When doing the oil change and topping up fluids you will need to use the following specifications:

Engine Size	8 Cyl. 5.7L Gas
Motor Oil	0W20
Oil Capacity w/Filter	7.9 US qt. (7.5L)
Brake Fluid	Dot 3
Engine Coolant	Toyota Super Long Life Coolant
Automatic Transmission	Toyota Genuine ATF WS
Front Differential	Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent
Rear Differential	Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent
Transfer Case	SAE 75W90

You can cross reference the following Purolator filter numbers for your own application:

Engine Size	8 Cyl. 5.7L Gas
Oil Filter	L25702
Air Filter	A55799
Cabin Filter	C35667

The 2013 Toyota RAV4 EV is a fully electric vehicle.  This vehicle will not require an oil change nor does it have a oil light to reset.  However, if you are servicing this vehicle here are the fluid specs:

Engine Size	Electric
Motor Oil	N/A
Oil Capacity w/Filter	N/A
Brake Fluid	Dot 3
Heater Coolant	Toyota Super Long Life Coolant
Motor Coolant	Zerex G 48 or Glysantin G 48 only
Automatic Transmission	Mobil Dexron VI

You can cross reference the following Purolator filter numbers for your own application:

Engine Size	Electric
Cabin Filter	*Dealer Part

 *At the time of this posting being published

The 2013 Toyota RAV4 is offered in a gasoline model.  After performing the oil change the maintenance data will need to be reset.  Follow these steps to reset this light:

Vehicles without a smart key system

1. Switch the display to the trip meter A and then turn the engine switch to the “LOCK” position.

2. While pressing the “DISP” button, turn the engine switch to the“ON” position (do not start the engine).

3. Continue to press and hold the button until the trip meter displays “000000”.

4. Start the engine and verify the indicator has been reset.

Vehicles with a smart key system

1. Switch the display to the trip meter A and then turn the engine switch off.

2. While pressing the “DISP” button, turn the engine switch to IGNITIONON mode (do not start the engine).

3. Continue to press and hold the button until the trip meter displays “000000”.

4. Start the engine and verify the indicator has been reset.

 When doing the oil change and topping up fluids you will need to use the following specifications:

Engine Size	4 Cyl. 2.5L Gas
Motor Oil	0W20
Oil Capacity w/Filter	4.6 US qt. (4.4L)
Brake Fluid	Dot 3
Engine Coolant	Toyota Super Long Life Coolant
Automatic Transmission	Toyota Genuine ATF WS
Rear Differential	Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent
Transfer Case	Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent

You can cross reference the following Purolator filter numbers for your own application:

Engine Size	4 Cyl. 2.5L Gas
Oil Filter	L25608
Air Filter	A25786
Cabin Filter	*Dealer Part

4 CYL. 2.5L Gas

 

*At the time of this posting being published

The 2013 Toyota Prius V is offered in a hybrid gasoline model.  After performing an oil change the maintenance data will need to be reset.  Follow these steps to reset this light:

1. Press the "ENGINE START STOP" switch once (do not start engine) or turn ignition key to run (one position before starting engine).

2. Ensure Trip Metre A reading is shown.  Turn the ignition off.

3. While holding the MPH or KM/H button turn the ignition on (do not start engine).

4. Continue to press and hold the button until the trip meter displays "000000" and the display indicates the reset is complete.

5. Turn the ignition off and then start the engine to verify the indicator has been reset.

 When doing the oil change and topping up fluids you will need to use the following specifications:

Engine Size	4 Cyl. 1.8L Gas
Motor Oil	0W20
Oil Capacity w/Filter	4.4 US qt. (4.2L)
Brake Fluid	Dot 3
Engine Coolant	Toyota Super Long Life Coolant
Automatic Transmission	Toyota Genuine ATF WS

You can cross reference the following Purolator filter numbers for your own application:

Engine Size	4 Cyl. 1.8L Gas
Oil Filter	L16311
Air Filter	A26114
Cabin Filter	C35667

4 Cyl. 1.8L Hybrid

https://www.oilreset.com

The 2013 Toyota Prius PHV is offered in a hybrid gasoline model.  After performing an oil change the maintenance data will need to be reset.  Follow these steps to reset this light:

1. Press the "ENGINE START STOP" switch once (do not start engine) or turn ignition key to run (one position before starting engine).

2. Ensure Trip Metre A reading is shown.  Turn the ignition off.

3. While holding the MPH or KM/H button turn the ignition on (do not start engine).

4. Continue to press and hold the button until the trip meter displays "000000" and the display indicates the reset is complete.

5. Turn the ignition off and then start the engine to verify the indicator has been reset.

When doing the oil change and topping up fluids you will need to use the following specifications:

Engine Size	4 Cyl. 1.8L Gas
Motor Oil	0W20
Oil Capacity w/Filter	4.4 US qt. (4.2L)
Brake Fluid	Dot 3
Engine Coolant	Toyota Super Long Life Coolant
Automatic Transmission	Toyota Genuine ATF WS

You can cross reference the following Purolator filter numbers for your own application:

Engine Size	4 Cyl. 1.8L Gas
Oil Filter	L16311
Air Filter	A26114
Cabin Filter	C35667

4 Cyl. 1.8L Hybrid

https://www.oilreset.com

The 2013 Toyota Prius C is offered in a hybrid gasoline model.  After performing an oil change the maintenance data will need to be reset.  Follow these steps to reset this light:

1. Press the "ENGINE START STOP" switch once (do not start engine).

2. Ensure odometer reading is shown.  Turn ignition off.

3. Press the "ENGINE START STOP" switch once (do not start engine).  The multi-information screen will be displayed for a few seonds.  While it is being displayed press the TRIP switch 3 times and hold it on the third time.

4. Continue to press and hold the button until the trip meter displays "000000".

5. Turn the ignition off and then start the engine to verify the indicator has been reset.

 When doing the oil change and topping up fluids you will need to use the following specifications:

Engine Size	4 Cyl. 1.5L Gas
Motor Oil	0W20
Oil Capacity w/Filter	3.6 US qt. (3.4L)
Brake Fluid	Dot 3
Engine Coolant	Toyota Super Long Life Coolant
Automatic Transmission	Toyota Genuine ATF WS

You can cross reference the following Purolator filter numbers for your own application:

Engine Size	4 Cyl. 1.5L Gas
Oil Filter	L14476
Air Filter	*Dealer Part
Cabin Filter	*Dealer Part

 *At the time of this posting being published

4 Cyl. 1.5L Hybrid

https://www.oilreset.com

The 2013 Toyota Prius is offered in a hybrid gasoline model.  After performing an oil change the maintenance data will need to be reset.  Follow these steps to reset this light:

1. Press the "ENGINE START STOP" switch once (do not start engine) or turn ignition key to run (one position before starting engine).

2. Ensure Trip Metre A reading is shown.  Turn the ignition off.

3. While holding the MPH or KM/H button turn the ignition on (do not start engine).

4. Continue to press and hold the button until the trip meter displays "000000" and the display indicates the reset is complete.

5. Turn the ignition off and then start the engine to verify the indicator has been reset.

When doing the oil change and topping up fluids you will need to use the following specifications:

Engine Size	4 Cyl. 1.8L Gas
Motor Oil	0W20
Oil Capacity w/Filter	4.4 US qt. (4.2L)
Brake Fluid	Dot 3
Engine Coolant	Toyota Super Long Life Coolant
Automatic Transmission	Toyota Genuine ATF WS

You can cross reference the following Purolator filter numbers for your own application:

Engine Size	4 Cyl. 1.8L Gas
Oil Filter	L16311
Air Filter	A26114
Cabin Filter	C35667

4 Cyl. 1.8L Hybrid

https://www.oilreset.com

The 2013 Toyota Matrix is offered in a gasoline model.  After performing an oil change the maintenance data will need to be reset.  Follow these steps to reset this light:

1. Press the "ENGINE START STOP" switch once (do not start engine) or turn ignition key to run (one position before starting engine).

2. Ensure Trip Meter A reading is shown.  Turn the ignition off.

3. While pressing the Trip Meter reset button, press the "ENGINE START STOP" switch once (do not start engine) or turn ignition to run (one position before starting engine).

4. Continue to press and hold the button until the trip meter displays "000000".

5. Turn the ignition off and then start the engine to verify the indicator has been reset.

When doing the oil change and topping up fluids you will need to use the following specifications:

Engine Size	4 Cyl. 1.8L Gas	4 Cyl. 2.4L Gas
Motor Oil	0W20	OW20
Oil Capacity w/Filter	4.4 US qt. (4.2L)	4.0 US qt. (3.8L)
Brake/Clutch Fluid	Dot 3	Dot 3
Engine Coolant	Toyota Super Long Life Coolant	Toyota Super Long Life Coolant
Manual Transmission	TOYOTA Genuine Manual Transmission Gear Oil LV or gear oil that meets API GL-4 and SAE 75W specifications	TOYOTA Genuine Manual Transmission Gear Oil LV or gear oil that meets API GL-4 and SAE 75W specifications
Automatic Transmission	Toyota Genuine ATF WS	Toyota Genuine ATF WS
Rear Differential	Hypoid gear oil API GL-5	Hypoid gear oil API GL-5
Transfer Case	Hypoid gear oil API GL-5	Hypoid gear oil API GL-5

You can cross reference the following Purolator filter numbers for your own application:

Engine Size	4 Cyl. 1.8L Gas	4 Cyl. 2.4L Gas
Oil Filter	L16311	L14677
Air Filter	A25655	A45650
Cabin Filter	C25851	C25851

4 Cyl. 2.4L Gasoline

https://www.oilreset.com